MICRO SET

Micro Set is a very versatile decal setting solution that does several things to Microscale Decals to improve application. Micro Set should be applied to the surface of the model where you will be sliding the decal off the paper backing. Micro Set prepares the surface with special wetting agents that cut the oils in new paint and converts the adhesive on the back of the decal to a stronger and longer lasting one. In addition, Micro Set slightly softens the decal film to make it more flexible so that it will conform better to the model's surface. Better adhesion of the decal to the model prevents tiny air bubbles from forming and results in an invisible carrier film for the so-called "painted on look." To apply Micro Set: Use a soft flat artist's brush and apply Micro Set where you are going to apply the decal. Then slide the decal off the backing paper using a small pointed tip synthetic bristle brush to carefully position the decal in its proper position. Blot the decal carefully with a tissue or paper toweling, being careful not to disturb its position. Allow the decal to dry overnight. It will then be ready for a protective coat of Micro Coat Flat, Satin or Gloss.
$12.50
8+ in stock

MICRO SOL

Micro Sol setting solution is for the most difficult irregular surfaces to be found on models. It completely softens the Microscale Decal, allowing it to drape down onto the surface of the model, conforming perfectly to surface irregularities without distortion. The most amazing results in seemingly impossible places are possible because Micro Sol actually makes the decal part of the painted surface. For that reason, you should coat Micro Sol on for only a few seconds and then leave it alone. It does the work. Do not touch until the decal has dried, as the decal is very soft at this stage and could be easily damaged. For the best results, first apply Micro Sol to prepare the surface and enhance the adhesive. Make sure the surface is free of particles that could get under the decal's film and cause a blemish. Then, when everything is dry enough that the decal will not move easily, apply Micro Sol with a small flat brush. Apply with as few strokes as possible so a not to disturb the decal. Then allow the decal to dry without disturbing it. One application is enough in most cases but, if necessary, a second application of Micro Sol can be helpful.
$12.50
8+ in stock

AK INTERACTIVE TOOLS - EASYCUTTING BOARD TYPE 1

This easycuting boards are re-usable and you only need to pay one time for this tool and have a good laser-carved base that will last forever ready to make all kinds of masks. The new Korean technology allow us to use this tools created specially for our hobby. Dimensions: 21.5 x 11.5 x 0.4
$30.00
2 in stock

TAMIYA PUTTY 32g

Cure your modeling masterpiece of any join lines, holes or indentations using this convenient material. It can be easily shaped using tools and sandpaper to gain the detailed finish you require. Contents: 32g
$10.00
1 in stock

ARMY PAINTER TOOLS - MINIATURE AND MODEL DRILL

The Drill is a well known and valuable tool for the converter and modeler. Drill holes in metal, resin and plastic miniatures with the drill bits provided in the handle case and can fit up to a 3mm drill bit size. 3x drill bits included:1.0mm1.4mm1.8 mm Complete your drill bit set with Drill Bits for more variety in bit sizes (10 bits) to finish any task involving miniatures. 
$34.00
0 in stock
Out of stock - Enquire

TAMIYA EXTRA THIN CEMENT (QUICK-SETTING) 40ML

Extra Thin Cement Quick-Setting (40 ml) Tamiya Extra Thin Cement is a widely popular glue among modelers around the world. You will find it in most modeler’s workshops. This version is the “quick setting” variant that dries around 4 times faster than the original Tamiya Extra Thin Cement, saving you time (and energy) holding parts in place! It also has less-tendency to seep out from part joints.Like the consistently of the original Extra Thin Cement product, the Quick Setting version is highly liquid and able to flow into small cracks, making it useful for attaching parts in very tight spaces. It can also be used to attach parts which have been pre-fitted by hand. Modeling Tip:It is best to use the Quick Setting Extra Thin Cement when you are looking to glue parts together very quickly, in order to move onto the next step of the building process faster. It is also recommended that you are sure of your parts attachment and fit when using this faster setting glue. The Quick Setting Cement typically dries in under 10 seconds, whereas the standard Extra Thin Cement dries within 40 seconds of application. Contents: 40ml. Bottle features a handy brush on the underside of the cap for easy application. Note: Not for use with elastomer (used on tank track parts, etc.) as it can cause brittleness. Original Tamiya Extra Thin Cement (Item 87038) is still recommended for use in situations where you wish to fill larger gaps and seams
$10.00
8+ in stock

VALLEJO HOBBY TOOLS - PRECISION MASKING TAPE - 18MMx18MM

Masking tape for model making, military modeling, plastic modeling and any miniature projects. No paint bleed or annoying paint lines. U.V. protected for masking in direct sunlight.Packaging: 2 units.
$8.00
2 in stock

MODIFX: FILE SET

This Modifx File set contains six (6) high quality Steel Files. These six (6) files are the most commonly used shapes and will help you clean and prepare your models for assembly as well as nicely remove mould lines. Works perfectly with both metal, resin and plastic miniatures.
$13.00
0 in stock
Out of stock - Enquire

MODIFX: PREMIUM NIPPERS

These Modifx Premium Nippers are; Made from high quality surgical stainless steel 5" length  Nicely forged, not ground down Durable snap back mechanism which wont catch your fingers.  Slim nippers blades to reach into sprues.
$37.00
0 in stock
Out of stock - Enquire

VALLEJO HOBBY TOOLS - MOULD LINE REMOVER

Vallejo expands the range of Hobby Tools to include a wide selection of highest quality precision tools, designed to cover all the needs of modellers and hobby fans. The tools are useful for easy assembly or for the most complicated set up, and are indispensable in all quality modelling projects.  This mould line cleaning tool is an essential addition to the modeler’s tool box. The stainless-steel edge complete with ergonomic handle makes easy work of smoothing away unwanted sprue or mould lines without damaging the models surface. Excellent for preparing surfaces for undercoating. Can be used on plastic model sprues, photo etch parts and metal War Game 28 mm miniatures.
$18.00
0 in stock
Out of stock - Enquire

MODIFX: CUTTING MAT - A4

This is for one (1) Modifx Cutting Mat Dimensions 300mm x 210mm
$18.00
0 in stock
Out of stock - Enquire

MODIFX: MODELING DRILL SET (WOOD HANDLE)

This Modifx Modeling Drill Set contains; - one (1) high quality Wooden handle Pin Vice / Hobby Drill - six (6) Drill bits: 1 x 2.0mm,1x 1.25mm, 2 x 0.85mm, 2 x0.5mm  
$19.00
0 in stock
Out of stock - Enquire

AMMO BY MIG ACCESSORIES EXTRA THIN CEMENT (POLYESTER PLASTIC GLUE)

Extra thin plastic cement. Hold the parts together, apply the cement to the joint and it will draw itself into the gap by capilaryty action. Completely dries in 10 minutes.
$12.00
0 in stock
Out of stock - Enquire

VALLEJO HOBBY TOOLS - PIN VICE - DOUBLE ENDED, SWIVEL TOP

Handy holder for drills, taps, pins etc. Includes: 2 reversible collets with capacities 0 to 1.2mm, and 1.3 to 2.4mm and 0.8 to 2.0mm, and 1.8-2.9mm. Incorporating swivel head for comfort and efficiency.
$25.00
0 in stock
Out of stock - Enquire

VALLEJO HOBBY TOOLS - FLUSH CUTTER

This flush cutter is perfectly designed for precise and intricate cuts in compact places. Excellent for flush cuts in thin wire, photo-etched parts, soft metal and plastic. For general hobby and modeling applications.
$30.00
0 in stock
Out of stock - Enquire

TAMIYA EXTRA THIN CEMENT 40ML

This is a 40ml Bottle of Tamiya's Extra Thin Cement. Age: 14 years and up Item no: 87038 Approx product dimensions: 4 x 6 x 4 cms Contents: 1 Bottle of Extra Thin Cement Volume: 40 ml This cement is extremely useful when gluing styrene plastic parts to a desired position while holding them in place together. The thin cement flows smoothly between the gaps of the fitted parts by capillary action. The plastic screw-on lid has an applicator brush attached. The pointed applicator tip makes it easy to put the cement where desired. Clear liquid. Glass bottle. Made in Japan
$10.00
8+ in stock

ARMY PAINTER - TOOLS HOBBY KNIFE

The Hobby Knife is essentially a surgical scalpel made or miniatures. Razor sharp and very precise, it is a fundamental tool for all wargamers. - IDEAL FOR CUTTING IN PLASTIC OR TINY METAL BITS- SAFETY GRIP HANDLE!- RAZOR SHARP FOR PERFECT CUTS
$22.00
0 in stock
Out of stock - Enquire

MODIFX DRILL BITS - 0.85MM (5 PACK)

This Stainless Steel High Speed Drill Bit is to be used for drilling holes for the 0.85mm Brass Rods which are used for pinning miniatures. This pack contains 5pcs.   
$5.50
0 in stock
Out of stock - Enquire

MODIFX SIDE CUTTERS

Modifx Side Cutters for modelling; - Really sharp points - long reach - durable return mechanism (not a spring) - suitable for both plastic and metal miniatures - affordable
$12.50
0 in stock
Out of stock - Enquire

MODIFX DRILL BITS - 0.50MM (5 PACK)

This Stainless Steel High Speed Drill Bit is to be used for drilling holes for the 0.50mm Brass Rods which are used for pinning miniatures. This pack contains 5pcs.   
$5.50
0 in stock
Out of stock - Enquire